Phoenix terminal is a type of equipment used for electrical wiring, its application scope is more and more widely, in use in order to smooth the completion of the work, then we should pay attention to some matters, let's talk about it.

　　拧紧力要适中。避免用力过大来松开螺栓和螺母。如果发现螺栓和螺母有松动，请立即更换，不要凑合工作。用螺丝刀拧紧或松开菲尼克斯端子的螺母时，一定要用螺丝刀用力拧紧螺丝，然后再拧紧或松开，以免螺丝刀与螺丝跑偏，造成螺丝损坏，不易拆卸，特别是在吊箱。普通空气开关。

　　Tightening force should be moderate. Avoid using too much force to loosen bolts and nuts. If the bolts and nuts are found to be loose, please replace them immediately, do not work at all. When using a screwdriver to tighten or loosen the nut of phoenix terminal, make sure to tighten the screw with a screwdriver and then tighten or loosen the screw. Otherwise, the screw may be damaged and difficult to remove, especially in the hanging box. Common air switch.

　　如发现螺栓、螺母难拆装，不必鲁莽行事，以免变形难拆装，应提供适度敲击，或加螺丝松动剂、稀硫酸等拆装前。不要用虎钳拧紧或松开螺栓和螺母，以防损坏。使用活动扳手时，应调整开口，以免螺栓、螺母损坏变形，造成拆卸困难。同一个菲尼克斯端子允许连接两根以上同类型、同规格的电线。

　　If bolts and nuts are found to be difficult to disassemble, there is no need to act rashly to avoid deformation and disassembly. Moderate percussion should be provided, or screw loosening agent and dilute sulfuric acid should be added before disassembly and assembly. Do not tighten or loosen bolts and nuts with a vise to prevent damage. When using an adjustable wrench, adjust the opening to avoid damage and deformation of bolts and nuts, which may cause difficult removal. The same Phoenix terminal can be connected to more than two wires of the same type and specification.

　　对于容易松动或接触不良的接线端子，必须用“？”将接线器紧固在接线端子上。类型以增加总接触面积并避免松动。线接头或线头相互连接时，禁止修改中间的非铜或低导电性垫片。连接线材连接器时，规定接触区域清洁，无空气氧化。接线鼻或铜排连接时，接触表面后可将导电膏擦拭干净，然后拧紧。

　　For terminals that are easily loose or in poor contact, use? Fasten the connector to the terminal block. Type to increase the total contact area and avoid loosening. Do not modify the non-copper or low conductivity gasket in the middle of the connector or connector connected to each other. When connecting wire connectors, ensure that the contact area is clean and free from air oxidation. When connecting the wiring nose or copper bar, wipe the conductive paste clean after touching the surface, and then tighten it.

　　连接菲尼克斯端子的临时线时，应将单线铜线的规定端子对折一次，然后接到空气开关的下孔；单芯硬线应收在“？”键入空气开关的下孔。30KW及以上电机接线，规定电机组出线与电缆之间不得使用热镀锌螺母、平垫圈、扭簧垫圈等导电性能差的垫圈当用绝缘胶带缠绕电缆或其他机械设备以保持绝缘层时，电缆护套应按压力位置的1/2比例从一端到另一端缠绕，至少绕一圈。

　　When connecting the temporary line of Phoenix terminal, the specified terminal of single wire copper wire should be folded in half once, and then connected to the lower hole of air switch; Single core hard wire receivable in "?" Type the lower hole of the air switch. 30 kw and above motor wiring, rules between the electric wire and cable unit shall not be used galvanized nuts, flat washers, torsional spring washers and so on about the worse performance of conductive gaskets when wrapped with insulating tape cable or other mechanical device to keep insulation, cable sheath should press stress position of 1/2 scale from one end to the other side, at least around a circle.

　　好了，以上便是问题的相关解答内容了，希望对您有所帮助吧。那么如果您还有别的问题想要了解的话，欢迎您对点击http://www.jntongyu.com网址进行咨询！

　　Well, the above is the relevant answers to the problem content, I hope to help you. So if you have other questions to understand, you are welcome to click on the http://www.jntongyu.com website for consultation!